Archive for the ‘3D Stuffs’ Category

I finally managed to get the short sleeves in a state where I’m actually somewhat happy about them.

That’s a sleepless night of sculpting that I’m not getting back, but that’s ok.

I’ve also quickly added some non-final seams to the body, just to get things looking a bit better (the body will get its own sculpting pass once I have more details in).

Now that this (big) hurdle is out of the way, I guess the next step will be to get the corset/waist cincher in place and the skirt of the dress.

The sleeves… I was dreading this part, and I was right. It has been a bit of a pain so far. I’ve included various iterations, the “smooth” ones are a bit of a template for the next versions, kind of a rough “idea” of what those would look like if stuffed with cotton, just to get the volume right.

The next phase, which took a bunch of attempts was to make a version with those little pleats on the edge where the sleeves are glued into the body and into the cuff. That’s the step that took the longest so far, it is horrible, and I hate it. It is a flat sheet with all the pleated edges on it that is wrapped into a cylinder and then shaped in place with a lattice cage. I hate it, but it does the job.

I’m trying to get it as close to where I’d like it to be before I get into the sculpting. Mainly because I’m not very good at it (at all) so the more I can do beforehand, the less I’ll randomly stumble in the dark.

I need more practice, that’s for sure.

Oh yeah, one last thing. Someone was asking if it could be made lock-able like the Hired Help Uniform, so I quickly added a hypothetical lock point 🙂

A promising first modeling draft… and also more reference/sketches.

I realized that I hadn’t tried to put long sleeves on it, I’m very fond of the loose cuff variant, it looks very cute and comfortable. The closed cuff variant is more “formal” I suppose, if you can consider latex formal.

I haven’t made this “type” of model in a really long time, and that’s one of the reasons why I’ve been procrastinating so much about it. There is nothing I hate more than trying to get something right, over and over, only to end up trashing it all up because I’m not satisfied.

But this? So far I’m pretty satisfied.

The next step is either going to be the short sleeves, or starting on the waist & the corset that goes there.

I added a picture of the back, but there isn’t much going on there. Maybe that’s something I should fix at some point.

Over the past couple days I’ve moved fairly quickly through both the low-poly modeling of the Halloween claws, but also UV unwrapping, and made all the LOD sub-models for the left & right-hand variant (that’s right, all by hand because I’m such a glutton for punishment). There was a few failed attempts due to fingers clipping through (on my avatar at least) and some weird shading oddities that, I believe, are all fixed now.

I’ve separated each claw and its respective retainer ring so that you can show/hide whatever you want to use or not (I don’t use the retainer rings when I’m wearing gloves for instance).

The current texture is really, really basic with a tiny bit of shading (tin-table texture) and a smooth normal map. I want to make a few variants next week, (as long as time allows for it). Something metallic, maybe some engraving? I don’t really want to make them too similar to last year’s.

That being said, suggestions are welcome.

The new Halloween claw project started well!

This is another claw set that I wanted to make, and it felt like too small of a project for the store “proper” so I’m making it this year’s Halloween project. These have a bit of an upward curve, which I think looks really feminine.

I’m probably going to make the finger ring hide-able because personally I will probably wear these over gloves, and that’s where those would be attached.

But the option of a ring to hold them in place is still nice.

Like the other ones, they attach to the middle of the finger, I was initially going to make an anchor point for the fingertip, or a full finger sleeve, but it would cause issues with finger posing.

Here is some in-world tests for the nose hook project!

Two days making LOD meshes, fixing stupid mistakes and re-doing more LODs. This is going to be just as difficult to adjust as the raider harness gag I fear, and I couldn’t find a haircut that allowed to see the locking buckle, so I’m probably going to make the clickable section extra large…

~2100 Display weight for the entire assembly. As I had planned, the square rings can easily be stretched or squashed to add/remove a little bit of slack here and there and get it to look nice and tight.

I’ve also quickly made a handful of upturned nose poses from 5 to 20 degrees in +5 increments.

I will be out of town tomorrow, so it is unlikely that I will be able to work on this.

I dislike LOD making so much, sometimes. I don’t usually have to do “all” of them on objects that have no cavities, but on fiddly little things like that, it is preferable if I do “most” of them by hand.

There is still like… 3-4 hooks to do (nose & rear/neck), (these are pretty quick tho) and 2-3 strap sections.

It looks good, I can’t really complain, but that’s so many individual parts to prepare for upload.

I’ve also finalized

I have spent an incredibly long amount of time getting just those nose hook strap textures assembled, I ended up having to redo them a bunch of time, mainly because I wasn’t paying attention to what I was doing. That and some RL appointments, are my excuses for the lack of updates last week.

I really, really need to make myself a set of reusable textures for strap work, but once again… that’s not going to be for this project. Maybe the next one, if there is long enough piece of strap on it?

I still have to make LOD models for those and put together all the colors.

Nearly done, I swear!

I’ve finished up the different hooks (I’ll just put them in the “extra” box I guess), I’ve also made a “short” hook and connector strap to make it easier to fit it to the Raider Harness Gag it is incredibly short. It should give more options for adjustment too.

Sometimes I wish I did not need this much padding on textures, but that’s just how it is with SL: 4 additional pixels per island is what’s safe.

Texture resolution wise, it is on part with the gag straps and should end up looking about the same. The metal parts should be able to use the existing hardware textures but if it doesn’t cut it I’ll make a new one.

I hope this is still somewhat of an interesting update ^^.

I’ve sort of finished the high poly straps for the nose hook and & unwrapped them. Started putting the little details in too, stitches & grommets. I’ve also added rounded tips to the hook ends and a d-ring to act as a retainer for the adjustment strap.

The last picture is just a quick test for a method to model an inflatable ball hood. I just thought I’d post it since it looked neat. Maybe a project for later.